PRUVIA Carbon Loop
PRUVIA Overview · 9 chapters Sources
Thermochemical recycling · Europe · status Oct 2026

Europe burns its above-ground oil field. We crack it.

Every year Europe collects about 33 million tonnes of plastic waste, and roughly 70 % of it is incinerated or landfilled.1 That waste is long-chain hydrocarbon. PRUVIA breaks those chains back into circular naphtha, a liquid feedstock that petrochemical plants can use instead of fossil naphtha, keeping the carbon in the material loop.

Jump to the technology

Tap any station on the loop to open that module.

Carbon loop from plastic waste back to new polymers C–C–C–C CARBON STAYS IN THE LOOP
≈33 Mtpost-consumer plastic waste collected in Europe, 2024 (derived)1
70.4 %of it incinerated or landfilled, about 23 Mt1
29.6 %recycling rate of collected plastic waste, 20241
€0.80/kgEU levy on non-recycled plastic packaging since 20214
01 / POSITIONING

Where PRUVIA sits in the recycling landscape

Recycling is a toolbox. Clean, single-polymer streams such as PET bottles belong in mechanical recycling. The mixed, dirty, multilayer residue left after sorting has had only one destination so far: the incinerator. That residue is the market thermochemical recycling serves, as a complement to mechanical recycling.

Recycling routes at a glance

RouteWhat it doesBest inputOutput
MechanicalWash, melt, re-pelletClean mono-streamsRecyclate, often down-cycled
Solvent-basedDissolve polymer, remove additivesSelected polymers, e.g. PP, PSPurified polymer
DepolymerisationBack to monomers chemicallyPET, PA, PMMAMonomers
PyrolysisCrack chains with heat, no oxygenMixed polyolefins, sorting residuesPyrolysis oil to replace naphtha
GasificationPartial oxidation to CO + H₂Almost anything carbon-basedSyngas for methanol and more
ENGINEER VIEWPyrolysis keeps the carbon backbone largely intact as C₅–C₃₀ hydrocarbons, so its oil drops into existing steam crackers. Gasification breaks everything down to C₁ and has to rebuild, which costs more energy and capital per tonne of product.

Route profiles

Qualitative positioning on a 1–5 scale, PRUVIA assessment; higher is better on every axis. Mechanical recycling leads on maturity and cost, but scores low on repeatable cycles and food-contact grade (see 02). Not a measured dataset.

02 / MECHANICAL LIMITS

Why mechanical recycling hits a ceiling

A plastic product is a formulation: base polymer plus pigments, fillers, stabilisers and processing aids. Mechanical recycling melts the whole formulation and reshapes it. Additives stay in, chains get shorter, and quality falls with every loop. Thermochemical recycling breaks the polymer down to hydrocarbon building blocks, leaves the additives behind, and lets the cracker build fresh polymer.

PEPPPSpigmentfillerstabilisercontaminants (inks, residues)

Schematic. Shows the direction of each effect, not measured data.

Intrinsic limits on both sides

Both routes have real constraints. Mechanical recycling is cheaper and simpler when the input is clean. Thermochemical recycling takes the streams mechanical recycling cannot, at the cost of energy and plant complexity.

ConstraintMechanical recyclingThermochemical recycling
Additives & colourLocked inPigments, fillers and additives stay in the melt. Mixed colours end up grey or black.RemovedAdditives and fillers leave with the char. The oil carries only hydrocarbons, plus traces that upgrading removes.
Mixed polymersIncompatiblePE, PP and PS do not blend into a strong material. Multilayer films cannot be separated.ToleratedPolyolefins and PS all crack to hydrocarbons. PVC and PET still need to be limited.
Chain lengthDegradesEvery melt cycle shortens polymer chains, so properties drop and the material is eventually incinerated.ResetNew polymer is built from monomers, so each loop starts at virgin quality.
Food contactMostly PETEU rules recognise mechanical PET recycling as a suitable technology for food contact. Other polymers remain under assessment.16Virgin-gradeOutput is chemically identical to fossil-based polymer and suits food and medical packaging.
Energy & yieldLow energyWashing and remelting need comparatively little energy.Energy intensiveCracking needs heat, and part of the input becomes gas and char. MLM-R® uses both on site for heat and power.
Maturity & costEstablishedDecades of industrial practice, low capex per tonne.Scaling upFirst commercial plants are being built now. Scale and replication drive cost down.
03 / TECHNOLOGY

Thermochemical recycling, from first principles

Plastics are long chains of carbon atoms. Heat them without oxygen and the chains vibrate until bonds break into shorter, liquid-sized molecules. Temperature, residence time and how heat reaches the plastic decide what comes out.

STEP 1 · SOLID → LIQUIDMeltextruder

Shredded, densified plastic is heated until it becomes a viscous melt.

STEP 2 · LIQUID → VAPOURCrack450–550 °C · no oxygen

The melt breaks into shorter hydrocarbon chains, released as hot pyrolysis vapour.

STEP 3 · VAPOUR → LIQUIDCondensecooled to ambient

Vapours are cooled into liquid oil in the naphtha and gas-oil range. Non-condensable gas is used for energy.

400–600 °C · no O₂

Pyrolysis

Thermal cracking into oil, gas and a small solid residue (char). Main product is a liquid.

> 700 °C · limited O₂

Gasification

Partial oxidation to syngas (CO + H₂). Very robust to feed, but rebuilds chemistry from C₁.

300–450 °C · water, pressure

Hydrothermal

Supercritical water as reaction medium. Handles moisture well, needs high-pressure equipment.

Try it: crack the chains

Illustrative trend for a polyolefin-rich feed, shaped on published data: real mixed waste gives roughly 66–71 wt % liquid near 450–470 °C9; gas rises and wax falls with temperature10. Not PRUVIA process data.

ENGINEER VIEWPlastics are poor heat conductors and melt into a viscous phase, so heat transfer, not chemistry, often limits throughput. Indirectly heated reactors lose efficiency as walls foul with coke; carbon black and fillers end up as char that must leave the reactor continuously.

The core problem: plastic is an insulator

Polymers conduct heat poorly. In a reactor heated through its wall, the plastic near the wall overheats and cokes while the core stays too cold to crack. This is why many pyrolysis plants struggle to scale.

Indirect heating (common)Heat has to enter through the wall. The wall zone overheats and cokes (red), while the core stays too cold to crack (blue).
Direct heating (MLM-R®)Hot carrier particles heat the whole volume (orange). The lens zooms in: polymer chains in the melt film crack and rise as pyrolysis gas; part of the residue stays on the carrier as coke.
too cold to crackreaction window 450–550 °Coverheated, coking

Illustrative 2D heat model, not plant data. The percentage shows the share of the melt inside the 450–550 °C reaction window.

The MLM-R® loop: continuous pyrolysis with a circulating heat carrier

Simplified scheme. The reactor–regenerator pair follows the FCC principle, without a catalyst.
Melt inAn extruder feeds molten plastic into the reactor.
CrackHot heat carrier delivers heat directly into the melt. Vapour goes to condensation.
Char outChar sticks to the carrier particles and leaves the reactor with them.
RegenerateThe char is burned, which reheats and cleans the carrier. The carrier returns to the reactor.
Recover energyNon-condensable gas is split: a share fuels the regenerator, the majority goes to energy recovery and is converted to electricity.
ENGINEER VIEWThe reactor–regenerator pair mirrors Fluid Catalytic Cracking: a solid circulates between an endothermic reaction zone and an exothermic regeneration zone. No catalyst is required. Char and part of the non-condensable gas close the heat balance; the rest of the gas is converted to electricity.

Built on a refinery workhorse

MLM-R® is not a new reactor concept. It adapts Fluid Catalytic Cracking (FCC), which refineries have run at industrial scale since the 1940s, to mixed plastic waste. That gives proven operating windows, standard components and an established path to scale.

1940sFCC in commercial refinery service
>75 %product yield achieved at the Leuna demo plant
0catalyst, char disposal or significant process wastewater
Self-sustainingby-products cover process heat and feed power generation

What that means

Direct heating

Heat reaches the plastic through the carrier, not a fouling wall. Even temperature means consistent oil quality and more throughput per reactor volume.

Char becomes energy

Char is burned in the regenerator, so the residue becomes the process heat supply instead of a waste stream.

Robust and continuous

Carrier circulation keeps the reactor clean during operation, so the plant runs continuously on real waste.

Economically scalable

FCC-type equipment from established supply chains, in a standardised plant that can be replicated site by site.

04 / CHALLENGES & ANSWERS

Pyrolysis is hard. Solving it is our edge.

The industry's problems are well documented. Tap a card to see how each one is addressed.

05 / UPSTREAM · FEEDSTOCK

Where the feedstock comes from

After collection and sorting, clean mono-streams go to mechanical recyclers. What remains (mixed polyolefins, films, multilayers and sorting residues) is today mostly burned. That residual stream is PRUVIA's raw material.

Europe's collected plastic waste, 2024

Mt per year, EU27+3. Volumes derived from the shares reported by Plastics Europe for 2024 (29.6 % recycled, of which 12.4 points outside Europe; 21.5 % landfill; 70.4 % incineration and landfill ≈ 23 Mt)1,2. Rounded.

From yellow bag to reactor

COLLECTSeparate collectionLightweight packaging from households and commerce.
SORTSorting plantNIR sorting pulls out PET, PE, PP, metals and paper.
RESIDUEMixed fractionsMixed polyolefins and sorting residues, e.g. DKR-350.
PREPAREShred, clean, densifyRemove inerts, dry, agglomerate or pellet to spec.
CONVERTPRUVIA reactorContinuous cracking to pyrolysis oil.

Partner model for feedstock preparation

Feedstock preparation is done by specialised partners close to where the waste arises. They deliver densified material to specification, so each new market is opened together with local preparation partners.

→ → →

Feedstock check: is this bale suitable for pyrolysis?

Polyolefins (PE, PP) crack cleanly into oil. PET and other oxygen-bearing plastics add oxygen, water and char, and PVC adds chlorine. Adjust the mix to see how the stream would be rated.

Screening logic for illustration only; actual acceptance follows PRUVIA's feedstock specification and lab analysis.

06 / DOWNSTREAM · PETROCHEMICALS

Where the oil goes

Pyrolysis oil is an intermediate, not an end product. Its value depends on the route it takes and on whether regulation counts the result as recycled. Pick a route.

Cracker base

24.5 Mt/a

EU ethylene capacity, mostly naphtha-fed.12

Mass balance

Pyrolysis oil is co-fed with naphtha, and the recycled share is allocated to products by certified bookkeeping. Under EU rules, the share that becomes fuel does not count.5

Quality gate

Crackers accept chlorine only at single-digit ppm. Upgrading (hydrotreating, filtration, dilution) bridges oil and spec.8

07 / REGULATORY DRIVERS

The rules turn waste into demand

Binding recycled-content quotas create buyers who must source recycled carbon. Mass-balance rules decide whether chemically recycled carbon counts toward those quotas. In Germany, national quotas still favour mechanical recycling.

PPWR minimum recycled content in plastic packaging

Regulation (EU) 2025/40, Art. 73. Food-contact polyolefin packaging is hard to supply mechanically, which makes it the natural home for chemically recycled content.

ReFuelEU Aviation: SAF share at EU airports

Recycled carbon aviation fuels are eligible if they meet RED criteria6, a second outlet for pyrolysis products.

The supply gap behind the quotas

Meeting the PPWR targets for contact-sensitive packaging needs about 1.7 Mt of circular naphtha a year from 2030.17 Today's chemical recycling capacity in Europe covers a fraction of that, and several planned projects have been dropped.18

Capacities are plant input (Mt of plastic per year), converted to oil at the selected yield. Planned capacity counts pyrolysis projects only (1.7–1.9 Mt/a; midpoint used). Module size: 35 kt/a input, as built by PRUVIA.

08 / RESILIENCE & BASE CHEMICALS

An oil field above ground, inside Europe

Europe imports most of the crude behind its chemical industry. Its plastic waste is the exception: a carbon resource that is already here, collected every day, and close to the crackers that need feedstock. Turning it into circular naphtha keeps value, jobs and supply chains in Europe.

Domestic resource

≈23 Mt/a

of plastic waste incinerated or landfilled in Europe: carbon that could feed European crackers instead.2

Low-carbon feedstock

−1.0 t CO₂e

per tonne of mixed plastic waste pyrolysed instead of incinerated.10

Stronger sites

Local + certified

A regional, mass-balance-certified feedstock lets European crackers sell circular, lower-carbon products that brand owners need for their recycled-content targets.3,5

Why pyrolysis oil is a base chemical, not a fuel

Polyolefin pyrolysis oil is mainly paraffins and olefins in a similar carbon range to naphtha and light gas oil. In a steam cracker it becomes ethylene, propylene and aromatics, the building blocks of most plastics.

Typical carbon-number ranges, schematic.

What one module delivers

Incineration, mixed plastic waste
Pyrolysis, mixed plastic waste
EU own-resource rate, non-recycled packaging
Oil replaces naphtha

CO₂e from the third-party-reviewed Sphera LCA for BASF10; levy4; naphtha cracker olefin yield ≈ 50 %13. Independent LCAs report 28–31 % savings for unwashed DKR-35011, so results depend on the feed.

09 / PRUVIA

From pilot to commercial plant

The MLM-R® process has been scaled in stages: verified in a pilot plant, then proven at industrial demonstration scale. The first commercial plant is next. After that, the standardised 35 kt/a module is replicated site by site.

Technology readiness

Company information19. TRL scale as used in EU Horizon programmes: 4–5 validated in a relevant environment, 7 demonstrated in an operational environment, 9 proven in commercial operation.

Sites

Gendorf: the de-risked first plant

ProvenTechnologyDemonstrated at TRL 7 in Leuna with >75 % yield; patents filed in EU, US, Canada, India and China.
ContractedFeedstockLong-term supply agreements, deliberately dual-sourced.
ContractedOfftakeMulti-year pyrolysis oil contracts with industrial buyers.
SecuredLocationPlot in the Infraserv Gendorf chemical park. Infraserv is landlord and provides administration, utilities and lab services.
AdvancedEngineeringFEED completed; plant structured in package units.
IdentifiedCore equipmentEstablished FCC equipment specialist for engineering, manufacturing and service.

Replication: what a rollout adds up to

Illustrative rollout of standardised 35 kt/a modules after the first commercial plant. Adjust the pace.

Years counted from the first commercial plant. CO₂ saving uses 1.04 t CO₂e per tonne of waste vs incineration (BASF/Sphera LCA)10; plants assumed at full output from their first year.

“Plastic is not the enemy — inaction is. Together, we can transform a crisis into a new industrial revolution.”MARTIN NITZ · CEO, PRUVIA

Regulation creates the buyers, crackers need domestic feedstock, and the waste already exists. PRUVIA supplies the conversion step between them.

Back to the loop ↺
SOURCES

Public sources

All figures come from public sources, checked 3 October 2026. Qualitative ratings and illustrative models are marked where they appear.

  1. Plastics Europe, The Circular Economy for Plastics – A European Analysis (2024 data), as reported by Fruit Today.
  2. Same report, as reported by NewsPackaging (23 Mt to incineration and landfill; exports).
  3. Regulation (EU) 2025/40 (PPWR), Art. 7 targets: Measurlabs; timeline incl. methodology act due 31 Dec 2026: Avery Dennison.
  4. European Commission, Plastics own resource (€0.80/kg).
  5. SUPD implementing decision on mass balance, approved 6 Feb 2026: S&P Global; details: renewable-carbon.eu.
  6. European Parliament OEIL, ReFuelEU Aviation summary.
  7. § 42 VerpackDG; Bundesrat Drucksache 377/26 (Beschluss), 10 Jul 2026.
  8. Kusenberg et al., Opportunities and challenges for post-consumer plastic waste pyrolysis oils as steam cracker feedstocks, 2022.
  9. Oil Production by Pyrolysis of Real Plastic Waste (70.6 wt % at 460 °C); Continuous flow pyrolysis of virgin and waste polyolefins (66 wt % waste).
  10. BASF / Sphera, LCA ChemCycling™ (739 vs. 1,777 kg CO₂e/t).
  11. Utrecht University, Pyrolysis of Dutch mixed plastic waste: lifecycle GHG.
  12. Wood Mackenzie / Citi via Polymerupdate; closures: S&P Global.
  13. Portfolio Planning Plus (naphtha cracker ≈ 50 % olefin yield).
  14. Hellenic Shipping News, European naphtha market, 2026.
  15. Plastics Europe, chemical recycling investment plan, via Waste Management World.
  16. Commission Regulation (EU) 2022/1616 on recycled plastic materials intended to come into contact with foods.
  17. Roland Berger via EUWID, Jun 2025 (≈ 1.7 Mt/a circular naphtha from 2030).
  18. Fraunhofer UMSICHT, Chemical Recycling Europe Map, Oct 2025.
  19. PRUVIA GmbH, company information on pilot plant, demo plant and MLM-R® technology, pruvia.com.